Product ID:NYLON 6,6 WEBBING;PART A OF 3 PARTS
MSDS Date:02/10/1992
FSC:1730
NIIN:00-079-2931
Kit Part:Y
MSDS Number: BPMPG

ELIZABETH WEBBING MILLS

PAWTUCKET, RI 02862
US

Emergency Phone: 401-723-0500 PREM AMIN

Info Phone: 401-723-0500 PREM AMIN

Cage: 85938

WECKWORTH MFG INC (316-263-3286)

516 ST LOUIS, MO 63166-0516 US

Telephone: 314-232-0232

Cage: 9J595

POLYAMIDE NYLON 6,6

CAS: 32131-17-2

Fraction By Weight: >99%

NON HAZARDOUS ADDITIVES

Fraction By Weight: <1%

OSHA PEL NOT RELEVANT

ACGIH TLV: NOT RELEVANT

Routes of Entry: Inhalation:NO Skin:NO Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:NON-HAZARDOUS AS SUPPLIED.HOWEVER,IF
MATERIAL IS HOT CUT TWO HAZARDS CAN ARISE:MOLTEN PLASTIC CAN BURN
SKIN AND SMOKE CAN CONTAIN HIGH LEVELS OF CARBON MONOXIDE(A
POISONOUS GAS).
Explanation of Carcinogenicity:THIS COMPOUND CONTAINS NO INGREDIENTS AT
CONCENTRATIONS OF 0.1% OR GREATER THAT ARE CONFIRMED OR SUSPECTED
CARCINOGENS.
Effects of Overexposure:THE SYMPTOMS OF CARBON MONOXIDE INTOXICATION
ARE HEADACHE, NAUSEA, WEAKNESS, DIZZINESS AND CONFUSION.
Medical Cond Aggravated by Exposure:NONE NOTED.

First Aid:IF MOLTEN PLASTIC COMES IN CONTACT WITH SKIN,IMMEDIATELY
PLUNGE THE AREA INTO COLD WATER.DO NOT ATTEMPT TO PEEL MOLTEN
PLASTIC AWAY FROM THE SKIN.GET MEDICAL ATTENTION FOR THE BURN.IF
FUMES FROM MOLTE N PLASTIC CAUSE HEADACHE,DIZZINESS,DROWZINESS OR
IRRITATION, MOVE TO FRESH AIR.

Flash Point Method:TCC
Flash Point:617F,325C
Extinguishing Media:USE WATER FOG, CARBON DIOXIDE, FOAM OR DRY
CHEMICAL.
Fire Fighting Procedures:CO,CO2,NOX AND NH3 CAN FORM DURING HIGH
TEMPERATURE FIRE.FIRE FIGHTERS SHOULD USE SELF-CONTINED BEATHING
APPARATUS.
Unusual Fire/Explosion Hazard:COMBUSTION OR HEAT OF FIRE MAY PRODUCE
HAZARDOUS DECOMPOSITION PRODUCTS AND VAPORS.

Spill Release Procedures:SWEEP UP AND PLACE IN AN APPROPRIATE DISPOSAL
CONTAINER.

Handling and Storage Precautions:KEEP AWAY FROM STRONG OXIDIZING
AGENTS.WEAR PROTECTIVE EQUIPMENT TO PREVENT PHYSICAL HAZARDS TO THE
SKIN AND EYES.
Other Precautions:NONE

Respiratory Protection:USE A NIOSH APPROVED RESPIRATOR IF OSHA PEL OF
ANY FUME COMPONENT IS EXCEEDED DURING PROCESSING.
Ventilation:USE VENTILATION DURING HOT CUTTING PROCEDURES.
Protective Gloves:NEED AND TYPE BASED ON WORK OPERATION.
Eye Protection:NEED AND TYPE BASED ON WORK OPERATION.
Other Protective Equipment:COLD WATER SHOULD BE AVAILABLE AS FIRST AID
FOR BURNS DURING HOT CUTTING OPERATIONS.
Work Hygienic Practices:AVOID PHYSICAL DAMAGE TO THE SKIN AND EYES.
Supplemental Safety and Health
KEY1:N1

HCC:N1
Melt/Freeze Pt:M.P/F.P Text:489F,254C
Spec Gravity:1.14
Evaporation Rate & Reference:UNKNOWN (N-BUTYL ACETATE)
Solubility in Water:NEGLIGIBLE
Appearance and Odor:SOLID, ODORLESS,VARIOUS COLORS.

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AGENTS AND ACIDS.
Stability Condition to Avoid:HIGH HEAT, OPEN FLAMES AND OTHER SOURCES
OF IGNITION
Hazardous Decomposition Products:CO,CO2,NOX AND NH3 CAN FORM DURING
HIGH TEMPERATURE FIRE.

Waste Disposal Methods:MATERIAL IS GENERALLY CONSIDERED TO BE
NON-HAZARDOUS,BUT REGULATORY PROVISIONS MAY REQUIRE TESTING TO
DETERMINE IF THE SPECIFIC MATERIAL MEETS ALL OF THE GUIDELINES.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.